Cutting laminate countertop with backsplash

A laminate countertop should be accompanied by a laminate backsplash. Normally, the backsplash is cut before it is installed. Before installation, you can set the laminate piece on two sawhorses for cutting. Laminate countertops usually come in one piece that combines the actual countertop and the backsplash. You can buy a circular saw and the rest of the tools required to cut a laminate countertop at a home improvement or hardware store.

This video shows how to cut a laminate countertop. The instructions on this video shows a degree, STRAIGHT CUT. If you are needing to miter a degree angle, I have anther video for that on my. You’ll get tips on layout, cutting without chipping, and how to make a cut that’s too close to the backsplash for a jigsaw to make.

Guide On How To Remove Laminate Backsplash. We offer a variety of laminate , solid surface, and quartz countertops , as well as in-stock laminate countertops to match any style. Recently I ran into an interesting situation. I was working on installing a sink in a laminate countertop.

In order to get it positioned right I had to place the template pretty close to the backsplash. Cut a dado in the backsplash. The laminate slips into the groove to give you a little wiggle room when you install it.

Remove the lumber after the cut along the backsplash and counter top is complete. Use a reciprocating saw to cut the existing laminate backsplash off the countertop (Image 3). The key is not to leave any edge sticking up. You build the substrate, cut out the laminate , and paste the two together with contact cement.

The problem is I will need to cut the countertop back. The backsplash is solid cherry, top is laminate. Here is how I made the cut. Measure and layout the mitre, cover the layout with clear packaging tape on the back side, cover the laminate side with clear packaging tape, flip the countertop over so that the laminate side is down (the saw blade is cutting up), start the cut from the backsplash side, and make the cut in one go. Slide the putty knife along the top edge and perimeter of the laminate to cut it loose from the glue.

Cut the sealant along the backsplash. Remove the corner bolts and screws from underneath the countertop holding it down to the. The distance from front-to-back will be shorter than the depth of the base cabinet. In this video, Jeff Johnson from Glen Allen, Va.

When you clean the countertop , dirt and debris will fall onto the drawer handles not onto the floor. Plus, you have so many patterns and colors to match your home décor. You can even get laminate that looks like nature stone. To do this, you have a choice in tool that needs to. Many laminate countertops come with an integral backsplash.

Pry it away carefully to avoid damaging the drywall. Nevertheless, the crucial aspect of cutting laminate countertop is to choose a blade with downward oriented teeth. In addition, the blade should have a medium to high tooth count. Using a blade with upward-orriented teeth is a rookie mistake, as in most of the cases it will chip the laminate countertop. We have a basement apartment and are replacing countertops before renting out.

Its a galley kitchen and the depths of the cabs are different. Both are standar but about inches different. Does anyone know if the premade laminate countertops come in different depths?

Also, is is possible to cut off the backsplash ? Use a roller to make sure the laminate is touching the countertop everywhere. Use a router with a laminate bit or a flush cut bit to trim the laminate to the self-edge. You can add a bevel to the countertop edge by cutting both the laminate and the self-edge with a bevel- cutting router bit. Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes.

Using Formica allows a homeowner to customize an area with a laminate that is durable and easy to clean. It easily shaved a few hours off my countertop installation. We ordered countertops without a backsplash because we wanted the wall tile to rest on the countertop. The techniques for installing a countertop with a backsplash are the same. Counters with a Backsplash.

But you’ll have to cut a larger hole in the drywall to tilt the countertop in (Photo 4). The other difference is in cutting the sink hole. Make sure the counter is well supported and bottom side up.

Retract the blade guard (disclaimer, never retract the guard) and start from cut the back splash first, up from the bottom so the saw cuts full depth. Edge treatments - ask if your dealer has samples. Is the laminate you like in stock or will it need to be special ordered? When you reference template you are making a template of the countertop ? I cut with a circular saw from the back side of the top to eliminate chipping the laminate.

Shop our selection of countertops and sheet laminate , available in a variety of styles, sizes and finishes.