How to cut a laminate countertop with a backsplash

A laminate countertop should be accompanied by a laminate backsplash. Normally, the backsplash is cut before it is installed. Before installation, you can set the laminate piece on two sawhorses for cutting. Put a piece of masking tape a least wide where you are going to cut. Mark you cut line on the tape and cut with a good sharp jig saw.

The tape will prevent the formica from chipping. If you bought a new sink, they probably gave you a template for the thing, that would be the easiest, probably. Do it this way for a perfect job. Use a router and carbide cutter to cut the long 4 and a fine tooth back saw to cut the vertical basksplash.

On the back side, mark the degree on the top to be cut as well as the verticle cut for. Laminate countertops usually come in one piece that combines the actual countertop and the backsplash. You can buy a circular saw and the rest of the tools required to cut a laminate countertop at a home improvement or hardware store. How to Cut Formica Countertop Already. Guide On How To Remove Laminate Backsplash.

This video shows how to cut a laminate countertop. The instructions on this video shows a degree, STRAIGHT CUT. If you are needing to miter a degree angle, I have anther video for that on my.

You’ll get tips on layout, cutting without chipping, and how to make a cut that’s too close to the backsplash for a jigsaw to make. You build the substrate, cut out the laminate , and paste the two together with contact cement. To do this, you have a choice in tool that needs to. Slide the putty knife along the top edge and perimeter of the laminate to cut it loose from the glue. The distance from front-to-back will be shorter than the depth of the base cabinet.

When you clean the countertop , dirt and debris will fall onto the drawer handles not onto the floor. Remove the lumber after the cut along the backsplash and counter top is complete. In this video, Jeff Johnson from Glen Allen, Va. The backsplash is solid cherry, top is laminate. The problem is I will need to cut the countertop back.

With laminate countertops , as any countertops , it is essential to also have a backsplash to protect the wall behind the countertop from moisture. Cut any narrow strips first, before rough- cutting the large kitchen countertop pieces. A coarse belt works best because it removes laminate and the substrate quickly yet neatly. Recently I ran into an interesting situation.

I was working on installing a sink in a laminate countertop. In order to get it positioned right I had to place the template pretty close to the backsplash. This step by step diy article is about how to cut a hole in laminate countertop. If you are remodeling your kitchen, you should probably know that cutting out holes in laminate countertops is require if you are fitting a sink or a gas stove. I cut most of the opening with a jigsaw equipped with a laminate -cutting blade.

These blades cut on the downstroke to prevent chipping. If the countertop has an integral backsplash , there’s usually not enough room for a jigsaw when making the rear cut (adjacent to the backsplash ). I make this cut with an oscillating multitool. Here is how I made the cut. Measure and layout the mitre, cover the layout with clear packaging tape on the back side, cover the laminate side with clear packaging tape, flip the countertop over so that the laminate side is down (the saw blade is cutting up), start the cut from the backsplash side, and make the cut in one go. The first step of the project is to mark the cut lines on the laminate countertop.

Once you are satisfie you can lay out your laminate and mark off where you will cut it to fit the lengths of the countertop. Cut : Cut your laminate using laminate sheers or a utility knife. Laminate sheers are a more expensive tool, but they offer a lower risk of cracks or other damage to the laminate surface. Cut the sealant along the backsplash.

Remove the corner bolts and screws from underneath the countertop holding it down to the cabinets. In some cases, you’ll also have to cut the glue. In that case, you must make the cut with the countertop upside down, so make the sink cutout after testing the fit but before joining any miter joints or attaching the countertop. Use trim router or table saw to cut 2-inch-wide strips of laminate for covering the edges of the 1¼-inch-thick counter.

Cut 1-inch-wide strips for covering the edges of the backsplash. Spray aerosol contact cement onto the back surfaces of the edge- laminate strips and along the edges of the countertop.