Best way to cut formica countertop

Re: Best way to cut a formica countertop Use a fresh, sharp blade in a circular saw, mark your cut line on the back, cut the splash first, then make the cut from the front edge to the backsplash. If you use a straight edge to guide the saw, the cut should be smooth enough to install an end cap if necessary, otherwise polish the edge with a belt sander before installing the end cap. Formica always cut from the back side. Draw the opening you want, and use a router.

Put a piece of masking tape a least wide where you are going to cut. Mark you cut line on the tape and cut with a good sharp jig saw. The tape will prevent the formica from chipping. Remove any masking tape used for the larger cuts with the circular saw.

You can buy laminate countertops in stock sizes that come in two foot intervals between and feet. Again, use masking tape where you will be cutting to protect from chipping. The manufacturer of your sink.

I just use a straight edge and cut a formica counter top from the back side with a circular saw. Installers often cut full sheets into manageable pieces with a table saw,. Handheld power saws cut on the upstroke,. Trimming the edges of laminate after it has been glued down calls for.

Use your straightedge and utility knife to cut along the line as accurately as possible. Use the utility knife first, as it will provide a goo clean cut. Be very careful not to get your fingers in the way of the blade. This video shows how to cut a laminate countertop. The instructions on this video shows a degree, STRAIGHT CUT.

When a business grows, new employees and machines become part of the operation. This means that employers need to make some changes to the office countertops or cabinetry. Same thing goes in a home setting.

You’ll get tips on layout, cutting without chipping, and how to make a cut that’s too close to the backsplash for a jigsaw to make. The problem is I will need to cut the countertop back. The backsplash is solid cherry, top is laminate. In case you do not have a rip fence or using it may not work in your case,. When you use an improvised guide, you may not be able to brace it down on both ends.

Measure the length needed for the counter top at multiple points with a tape measure. Lay a counter top on a stable surface with the laminated side facing down. Align the inside edge of a circular saw blade with the.

How to cut Laminate countertop – DIY This is a short video demonstrating how to cut laminate ( formica ) countertop without chipping with a circular saw. The best way to cut a laminate countertop is with a large stationary saw with 12- or 14-inch blades. Alternate methods are to use a jigsaw with a specialized laminate cutting blade or a circular saw with a shop-built jig to guide the cuts.

In this video, Jeff Johnson from Glen Allen, Va. To cut through laminate countertops, you can use a hand saw, but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the laminate face-side down and cut from the back to the front. We use a portable table saw, masking tape on the formica , and cut it from the formica side, right down the middle of the masking tape. It seems to me that my saw blade (just the blade) was over $10 but it does a great job and it can be resharpene so should last just about forever.

If the backsplash interferes with the saw shoe and prevents making the cut, turn the countertop over to complete the cut from the underside. If you choose this metho make this cut first. Again, don’t worry about any little chips that may occur. Cut slowly along the line.

The sink lip will cover them. Just wondering what the best way is to cut laminate counter tops. It is durable and comes in a variety of styles and colors, making it an ideal choice when improving your kitchen. I have done a couple , and they turned out O. While the material may look nice, I understand how it can be a struggle deciding how best to cut it and get it applied on your own. The following article will explain how to cut formica sheets in brief.

Techniques for rough- cutting laminate sheets, in the shop or on site. A laminate countertop installation is basically a grade-school cut -and-paste project writ large. You build the substrate, cut out the laminate, and paste the two together with contact cement. For example, when you install a sink in your kitchen or bathroom, you need to cut a hole in the countertop that is the same size as the sink. When cutting a countertop , you want to take care to avoid chipping or otherwise damaging the surface.

A chipped countertop can be a huge headache and very difficult to repair. Cutting a solid surface countertop is a straightforward task that can be carried out by DIY enthusiasts of all skill levels. Solid surface countertops provide an attractive and versatile alternative to conventional laminate materials, and can be shaped or formed using the same tools that are.