How to measure undermount sink

First you mount the sink in a plywood top over the cabinet. Then the stone fabricator will come out and measure the cabinet, location and dimensions of the sink, location and type of faucet. The counter man will cut the necessary holes in.

Hello There are many different stores that will do granite countertops for you. If you purchases a countertop through any of the stores they will have to send someone out to take measurements. Some will come out to give you an estimate on. How to Buy an Undermount Sink - Steps Make sure you have a waterproof countertop. Decide what type of material you want to use.

Install a new sink that is no deeper, wider or. Set the sink in a stable position for measuring. Hook the tab of the tape measure at the back of the outside rim of the sink and draw. Use a tape measure to learn the side-to-side width and the front-to-back length of the sink you are replacing. After that, measure height and depth.

Keep in mind that these are two different measurements. Start by measuring the cabinet size under your existing sink or where the new sink will go. The new sink should be approximately the same size. Here is how you measure for a perfect fit.

Vessel sinks , which sit on top of a counter or a vanity, can be tricky to measure because they tend to look like a bowl sitting on a counter. When you measure for a vessel sink , remember that there will be several inches of sink extending up from the vanity or counter, rather than dropping into it. Carefully remove the sink from the countertop and paper without moving the paper.

Use the framing square and straight edge to assist, if needed. Write down these measurements. If this is a simple replacement, measure the length, width and height of your current sink and choose one with the same measurements. Most sinks are around inches (8 cm) from the ground. Bathroom sinks can cost from under $1for a basic sink to several.

First, take out your measuring tape and keep it handy. Next, make sure you have a piece of paper and a pencil or pen handy to mark down your measurements. First, you will want to start with your edge or lip that you have on the counter.

Measuring for Your New Sink. These sinks are dissimilar to traditional sinks in which the the sink edges are visible over the countertop. Most kitchen sinks can fit an average cabinet depth of inches, but each kitchen sink has a minimum cabinet size requirement for proper fit. Undermount sinks are stylish and attractive, and if you measure and install them properly, they seldom leak.

A sink’s minimum cabinet size is a measurement indicating the least amount of under-cabinet and top counter space required for the sink to fit properly. Ken, an Elkay Sink Expert demonstrates how to measure an existing sink base to make sure you purchase the right Elkay sink size for your space. Great measuring tips for a remodel or replacement. How to measure undermount sink Undermount Sinks - Bathroom Sinks - The Home Depot Shop our selection of Undermount Sinks in the Bath Department at The Home. This will make the installation much easier and will cut down on excess work.

So the firs step is to remove the existing sink and with a cast iron sink , it is extremely heavy and the problem that we had is that you have to remove the sink from the bottom. Most professionals can install an undermount kitchen sink in minutes or less. With no rim to contend with, undermounts are the easiest to clean. To measure the depth, lay a straight edge across the top of the old sink.

Insert a ruler into the sink by the drain. Read the ruler by the straight edge. That is the depth of your current sink. You may have room for a deeper sink depending on the size of your garbage disposal, if you have one and location of your plumbing underneath.

Finally, since an undermount sink is highly valued in designer kitchens and bathrooms, it often raises the resale value of your home more than an overmount sink. Unfortunately, the selection of complementary countertop materials available for undermount sinks is a bit more limited. An undermount sink should always be flush with the undermount cut out. This will ensure that it will be flush versus having a lip. When measuring the sink , measure from the inside.

Sink Size Specs - Advice needed We are remodeling our Kitchen (Vancouver, BC) and I have a question on sink vs. Due to space restrictions etc, for our sink we have ordered a cabinet and were looking at the Blanco Sinkgranit Undermount 1. Licensed contractor Amy Matthews shows how to install a vanity with an undermount sink and faucet. The granite is then on top of the plywood and sits on top of the lip so that it looks built in. Triple-bowl sinks may measure up to 60″.

Irregular sizes are commonly found in bar and prep sinks. Sinks are generally between and inches deep. Select the appropriate type of replacement sink. Single- and double-bowl drop-in sinks can be installed into most countertop surfaces.

These instructions are for installing a drop-in sink.