Best tool to cut laminate countertop

It is not a hard job for a person that has done it before. You may get that say Rough. Installers often cut full sheets into manageable pieces with a table saw,. Handheld power saws cut on the upstroke,. Trimming the edges of laminate after it has been glued down calls for.

How to Cut a Laminate – Formica Countertop Tools. You can buy laminate countertops in stock sizes that come in two foot intervals between and feet. Again, use masking tape where you will be cutting to protect from chipping. The manufacturer of your sink. The best tool for cutting edge band strips is a laminate slitter.

The cutting wheels adjust for laminate thickness and leave finish-quality edges. Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes. If you want to achieve the best joints , you must use the right techniques on how to cut laminate countertops such as maintaining straight edges that are factory-cut. Countertop materials with square edges are easier to put together especially if the front edge has a curved finish.

Pull the tool along the wall to mark the cutting distance on the surface of the counter top. Because laminate countertop is a relatively soft material, a normal circular saw blade for cutting wood is capable of cutting through it with ease. According to WoodworkingTips. My two recommended tools for a rough cut are a table saw or pneumatic shears.

For a finish cut is a router with a Formica bit. To prevent chipping set up the table saw with a zero clearance throat and run a piece of masking tape down the finish side of the cut line. To cut through laminate countertops , you can use a hand saw, but a circular saw makes the job much quicker.

Because a circular saw can produce jagged edges and chip the laminate , your best bet is to lay the laminate face-side down and cut from the back to the front. Select the Right Blade Before you start in on cutting your laminate countertop, it’s of utmost importance. Simply put, certain types of blades are best for cutting certain materials. These tools can also rip cut, which means making straight cuts parallel with the grain.

Below are some of the most common tools available for shaping laminate and whether they are useful for your project. This is one of the best tools for this project. An old or dull blade can chip the laminate along the cutting line. Drill two starter holes in opposite corners just inside the cutting line. To summarize, getting laminate clean is a two-step process.

Simply roll the laminate trimmer over the edge of the countertop and the trimmer will create the perfect, smoothed cut for you. Without a Laminate Trimmer. If you do not have a laminate trimmer, do not worry. You can still easily trim your laminate with other tools. For this project, it is best to use a blade on your circular saw that is designed for fine cuts that has a narrow kerf and carbide tips.

When a business grows, new employees and machines become part of the operation. This means that employers need to make some changes to the office countertops or cabinetry. Same thing goes in a home setting. In such cases, you need to cut Formica countertop already installed in order to make way for new appliances or home remodelling.

This video shows how to cut a laminate countertop. In this video, Jeff Johnson from Glen Allen, Va. The instructions on this video shows a degree, STRAIGHT CUT. If you are needing to miter a degree angle, I have anther video for that on my. You also need a very good high speed saw.

For a few bucks they will cut it and put an appliance end cap. Can someone tell me the best way to cut the sink hole from experience. Is it best to fasten the counter to the cabinets and then cut it, or precut then turn it over and put in the sink. I saw a video that indicated it is much easier to attach the sink that way. Circular saw with a thin kerf (space left by cut of blade) carbide blade with teeth.

The best way to cut a laminate countertop is with a large stationary saw with 12- or 14-inch blades. Alternate methods are to use a jigsaw with a specialized laminate cutting blade or a circular saw with a shop-built jig to guide the cuts. This specialty blade has teeth that cut on the down stroke to prevent chipping. Quick and easy tips and tricks explaining how you can be sure you make nice, clean cuts when cutting a laminate countertop. This sounds difficult but is actually quite easy and allows you to see exactly where the cut is occurring without being inhibited by the frame of the jigsaw in any way.

What tool or blade do i need to cut this kind of counter. Best Answer: Too much of a chance for the tool to slip. Using the file reduces the chance of damaging the counter top.

I was using flimsy plastic saw horses to hold the sheet up and half way through the cut the weight of the sheet (because one of the saw horses collapsed) tore the sheet.