Saw to cut laminate countertop

Because laminate countertop is a relatively soft material, a normal circular saw blade for cutting wood is capable of cutting through it with ease. According to WoodworkingTips. To cut through laminate countertops , you can use a hand saw , but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate , your best bet is to lay the laminate face-side down and cut from the back to the front. The perfect saw blade to cut a laminate countertop is a circular miter saw.

You can also use a hand saw but a blade with a circular saw makes the job easier and quicker. After making the first cut , you need to install the fence guide perpendicularly and clamp into place tightly. Make sure the blade of the saw will go exactly over the cut line, otherwise the countertop won’t go over the cut line.

NOTE: When cutting countertop , use a fine-toothed plywood cutting blade to minimize chipping in the plastic laminate. The teeth of the saw blade enter the face of the plastic laminate , so chipping is minimal or nonexistent. If you replace a countertop in your kitchen or bathroom, you may need to cut the new countertop to fit the desired area. You can buy a circular saw and the rest of the tools required to cut a laminate countertop at a home improvement or.

Laminate countertops usually come in one piece that combines the actual countertop and the backsplash. Now I can cut the sides with a jigsaw. I’m using a laminate cutting jigsaw blade in the saw. This specialty blade has teeth that cut on the down stroke to prevent chipping. To prevent the cutout from breaking free of the countertop prematurely, which would damage the laminate , I screw a cleat to the cutout with single screw.

Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes. Using Formica allows a homeowner to customize an area with a laminate that is durable and easy to clean. Cutting a laminate countertop with a handsaw can be a challenge because the motion of the handsaw can crack or otherwise damage the laminate.

However, you can ensure the safety of the laminate countertop by following a straightforward procedure. The Bosch Daredevil is a 10-inch saw blade for laminate flooring that is perfect for cutting laminate floors and countertops. So we mark our cut , and then we align our cutting guide with that mark. The best way to cut a laminate countertop is with a large stationary saw with 12- or 14-inch blades.

Alternate methods are to use a jigsaw with a specialized laminate cutting blade or a circular saw with a shop-built jig to guide the cuts. The cut was nice and smooth. And I used a guide block to keep it straight.

In cutting the laminate , a circular saw to use is another option. The blade of the saw should have at least teeth to give the edges a clean finish. The blade should be positioned at the thickest part of the countertop and slowly start sawing with a steady movement. Remember to use a steady movement and cut slowly. If you are not able to cut right to the wall using a circular saw , you can finish the cut using an electric jig saw with a fine tooth metal blade or a special laminate blade.

When cutting the countertop chipping the laminate is your main concern besides making a straight line. A helpful hint to prevent chipping is to put masking tape over the line you are cutting. Also make your cuts on the good side of the countertop , which means the teeth of the saw enter the face of the laminate. Use a jigsaw with a laminate cutting blade (any high TPI blade will do the trick) to remove the excess Formica from the countertop , and to rough in any curves that your countertop may have. Step V: Cleaning Up the Edge.

Next, we’ll create a nicely finished edge for our countertop to complete the edge. When I make the final cut , I cut just a little outside of the line so that there is a slight amount more to remove. If you need the cutting a laminate countertop or flooring in the kitchen, you may need a suitable saw blade.

Don’t just come to the store to get the woodworker to make the cutting at your house! A laminate countertop should be accompanied by a laminate backsplash. Normally, the backsplash is cut before it is installed. Before installation, you can set the laminate piece on two sawhorses for cutting.

In order to make accurate sizes of Formica for your countertops , you will need to follow the above steps when making the laminate cuts with a table saw. Even though it is thicker, you still need to use a protective board on the table top of the. This step by step diy article is about how to cut a hole in laminate countertop.

Countertop laminate is thicker than cabinet mica. If you are remodeling your kitchen, you should probably know that cutting out holes in laminate countertops is require if you are fitting a sink or a gas stove. Cutting formica countertops to size involves sawing both the formica sheet and the particle board layer that gives the counter its strength.

These materials contain large amounts of glue that quickly dull the edges of saw steel that is not carbide-tipped.