Trimming laminate countertop end caps

Cover the exposed end of the countertop with a layer of wood glue. Center and press the buildup strip into place. Secure the buildup strip to the end of the countertop using four, 1-inch wood screws.

During installation, the hard qualities can lead to cracking and chipping especially when finishing edges and end caps. Countertop installers leave a small overlap that they trim later making the end cap a smooth joint. The end cap is a separate piece of plastic laminate glued to the raw exposed end of a countertop. Dimensions of standard kitchen end cap are 5(W) X approx.

Justin shows the quickest way to Install Formica Countertop End Caps. Trimming a countertop is a precision job that is perfect for the Dremel and its novice user. Cut a straight line and sand the edges. Included with this kit is left-hand end cap , right-hand end cap , buildup end strips, backsplash buildup blocks, package of nails and instructions.

We usually use a PB substrate, spray glue (propane tank style), laminate front edge, trim with trim router, file flat, then do the top. When we trim the top or the end caps of the blanks or backsplashes, we invariably scrape into the adjacent edge with the router. Or we cut heavy then file for hours.

Leave the glued end caps to dry for a few hours. Step 5: Rub some petroleum jelly along the surface of the end caps. The jelly is useful as a lubricant to prevent friction or damage to the countertop ’s laminate.

Using your router, trim away the excess caps from the edge of the countertop. Use a finer-grit paper and be patient. Position the end cap on the cut end of the countertop and align the angle and corner with the contour of the countertop’s surface. If your countertop has an exposed end that doesn’t butt against a wall or into a corner, you need to finish it by applying a laminate end cap — a piece of the laminate surface that covers the exposed end of the countertop substrate. The end cap kits that go with the post-form countertop I purchased have a lot of extra material left along the edges, too much just to file down.

I do not own a router or the laminate bit needed to cut it off per the instructions. It is standard laminated countertop that I had to attach to lower cabinets so tail guy and painter can keep going ( I know irony, me carpenter adjust for tiller and painter). Owner both laminate edge that I glued to countertop edge. Now no space for router to go all way around.

Can post picture of it tomorrow, before and after. Another flush trim formica end cap Q? A good laminate trimming bit from a reputable mfg is a cost savings in the long run. Kits usually come with one of each. End caps are precut to fit the counter profile but oversized at the back edge to allow for a scribed fit, so you need to do some trimming with a hand file. New laminate countertops are a fairly inexpensive way to freshen up a tired kitchen but it is important to get the installation right.

The edges of newly installed laminate countertop must be trimmed and can easily and quickly be done with a router. It is important to use the proper technique, however, to avoid damaging your new laminate. Look below for first hand experience and step by step instructions for painting laminate countertops. I have a pink bathroom sink that could benefit from this!

Great for giving a finished look thoughout the kitchen. Painting countertops instead of replacing. Comes with one left and right end cap to match exposed edges to the color and edge profile of your laminate countertop.

The problem is I will need to cut the countertop back. The backsplash is solid cherry, top is laminate. Find great deals on eBay for laminate counter tops. Flute Flush Trim Bit For trimming.

Finish trimming with a fine file, applying pressure only on the up strokes. Complete instructions are included in the end cap kit. Laminate Countertop End Cap Wall Sidesplash. To apply end caps using non pre-glued end caps , apply a contact adhesive to both the substrate and the laminate. Roll laminate with a J-roller.

End caps and other laminate edges sometimes come loose and can get broken off if not reglue but as long as the particleboard backer is in good condition, the fix is simple. Scrape off chunks of debris or dried lumps of glue from the end cap. We offer a variety of laminate , solid surface, and quartz countertops , as well as in-stock laminate countertops to match any style.