What type of saw blade to cut laminate countertop

If the countertop is preformed and not just a sheet of laminate, you have the chipboard below and the laminate glued to the top. Get as close to degrees as. Make sure you use the tape on either side of the cut on the laminate side. Also, make sure you use a NEW saw blade. Flip countertop upside down cut through the.

Take some advice, do not attempt to do this yourself. Un hook sink drain and water lines. To cut through laminate countertops , you can use a hand saw , but a circular saw makes the job much quicker. Because a circular saw can produce jagged edges and chip the laminate , your best bet is to lay the laminate face-side down and cut from the back to the front. Solved: What blade to use to cut counter top.

Put tape on the shoe of the saw to keep from scratching the laminate. The best way to cut a laminate countertop is with a large stationary saw with 12- or 14-inch blades. Alternate methods are to use a jigsaw with a specialized laminate cutting blade or a circular saw with a shop-built jig to guide the cuts. If you replace a countertop in your kitchen or bathroom, you may need to cut the new countertop to fit the desired area. Laminate countertops usually come in one piece that combines the actual countertop and the backsplash.

You can buy a circular saw and the rest of the tools required to cut a laminate countertop at a home improvement or. Align the inside edge of a circular saw blade with the cut line, with the other edge of the blade facing the piece of the counter top you are cutting off. Make a mark on the side of the saw guard. Because laminate countertop is a relatively soft material, a normal circular saw blade for cutting wood is capable of cutting through it with ease. According to WoodworkingTips.

NOTE: When cutting countertop , use a fine-toothed plywood cutting blade to minimize chipping in the plastic laminate. The teeth of the saw blade enter the face of the plastic laminate , so chipping is minimal or nonexistent. Cutting any counter top isn’t easy and requires a good saw blade and some patience.

I would use a circular saw with a fined toothed plywood blade to make the length cuts on the countertop. When cutting the countertop chipping the laminate is your main concern besides making a straight line. Use light pressure, and cut slowly to avoid chipping and scorching the laminate.

Cleaner cuts result if the formica is temporarily laid on waste plywood for support. Carbide router bits, jigsaw blades and circular saw blades will all work well on formica if proper guides and blade settings are used. A finish blade appropriate will be fine, BUT too if you choose to cut with a finish blade of a scroll saw for example, you might reverse the blade in a scroll saw to inflict the possibility of damage more to the underside of what is likely MDF Depending on blade Kerf and tooth size.

Nevertheless, the crucial aspect of cutting laminate countertop is to choose a blade with downward oriented teeth. In addition, the blade should have a medium to high tooth count. Using a blade with upward-orriented teeth is a rookie mistake, as in most of the cases it will chip the laminate countertop. The Bosch Daredevil is a 10-inch saw blade for laminate flooring that is perfect for cutting laminate floors and countertops. Installers often cut full sheets into manageable pieces with a table saw , which requires the extra step of providing support for the sheet on the out-feed side of the table as well as on the blade.

Saw the counter along the cut line with the handsaw. Hold the end of the blade that is by the handle of the saw on the edge of the countertop. Pull the full length of the saw toward your body in one smooth motion. This will provide a clean starting cut to start sawing. As you cut along the line you drew, use smooth back and forth motions with.

Down-Stroke Jigsaw Blades for Laminate. I am running into a problem when cutting a laminate countertop from the top side. Formica is a versatile, plastic laminate that comes in a wide range of colors, textures, and finishes. Using Formica allows a homeowner to customize an area with a laminate that is durable and easy to clean.

New innovations in Corian. The answer depends on the material the countertop is made of, and the precision of the desired cut : If the top is high pressure laminate , e. Formica, any saw , even a hand saw will do a fine job. Cut the pre-formed laminate from the back side with a carbide blade on a circular saw for strait cuts. In order to make accurate sizes of Formica for your countertops , you will need to follow the above steps when making the laminate cuts with a table saw. Even though it is thicker, you still need to use a protective board on the table top of the.

What blade do you recommend for a good cut and long life? The perfect saw blade to cut a laminate countertop is a circular miter saw. Countertop laminate is thicker than cabinet mica. You can also use a hand saw but a blade with a circular saw makes the job easier and quicker. Blade vibration or “resonance” can cause warping of the blade , chipping and splintering of material you’re cutting and may eventually damage your saw.

If you have the option, use a blade equipped with a heavy duty plate for added stability and to reduce vibration. So we mark our cut , and then we align our cutting guide with that mark. And that’s where the saw blade is going to go.

Fill Your Cart With Color today!