How to make plywood countertops

The best type of plywood is veneer plywood. Depending on where your countertop is going it may be necessary. As you begin cutting, it is a good idea to try to place the seams well. I think you would be surprised with the ease and cheapness of a concrete countertop versus a grout one. If you pour in place the two are pretty.

You need better support on top of the cabinets for a grout countertop than you do for a concrete. The stuff is lighter but more breakable. Grout is simply powder based concrete. Setup the countertop like you would for a tile countertop. It depends how your countertop was made.

If there is no seam between the backsplash and the horizontal suface, then you probably have a premade countertop that is screwed to the cabinets from underneath. Look inside your cabinets, and see. Set the fence on a table saw and cut a sheet. Measure the width of the countertop and add inch.

Place the plywood countertop on top of the cabinets. Draw a light pencil mark on the front of the cabinets where the interior. Apply glue to one of the 2-inch sides of the 2-inch material,. How to Build a Plywood Countertop Step 1. Plywood looks like crap on the edges, so I had to add a moulding at the front to cover up the ugly.

Plus, a curved moulding is a lot more comfortable on the wrists than a sharp countertop edge! After testing out the router bits we had on han I decided on a simple S-curve with a small fillet at the bottom. With the countertop in place, the backsplash is added.

It is attached to the wall with finishing nails. As with the countertop itself, make sure that any seams between different pieces of the backsplash substrate sit flush with one another. Anthony offered to cut a small piece of the scrap plywood to stick in that spot on the side to make it look one inch thick all around but I figured it was pointless.

Next on the list for this room – getting rid of that blah, crooked light fixture and adding some wallpaper to the wall above the countertop. Make sure your cleats are long enough to catch all the boards, yet short enough to not cause any problems with your cabinet structure. Use wood screws to attach the boards together with my Rockwell 3RILL , using 2-in each boar all the way down.

Stained plywood offers an economical alternative to expensive butcher block or tiled countertops. This video is unavailable. It can be prepared beforehand to make the staining process easier.

Attach 4-inch-wide plywood build-up strips around the perimeter underside of the counter , and along any seams. Use a block plane to trim the build-up strips flush with the counter edges. Lay plastic laminate sheet on top of counter and make a rough cut with a laminate router. Attach the plywood to the cabinet with a cordless screwdriver and screws.

Insert your screws up through the base cabinet into the bottom of the plywood. Use screws that are shorter than the thickness of the plywood to avoid breaking through. Find and save ideas about Plywood countertop on Pinterest. See more ideas about Plywood edge, Plywood shelves and How woodworking routers work. The only thing that can be considered difficult about countertops is that you have to be careful when working with laminate or it can break.

Grante laminate isn’t the only material kitchen countertops are made of, countertops can be covered with ceramic tile, made of Corian, or out of one of the more exotic materials, like marble or granite. Wood countertops can add a classic finish to any type of kitchen décor. So, I used that as a way to plan which side of the plywood would be the top and bottom so I could hide the splintered side underneath. As far as installation goes, I treated the countertop similar to how I installed the floating shelves on the right side: as one large shelf in need of support along three sides.

However, given the narrow space, the room’s dimensions were a little tricky to work around. Learn how to make old counter tops new again, step by step free training! Most countertops are covered with plastic laminate or tile. However, hardwood plywood is sometimes used for a more exclusive appearance. Use the flat end of the trowel to push the thin set over the surface of the plywood.

Anyway, I’ve used a similar process before to make a table top, and it turned out beautifully. So if you need a countertop , desk top, or table top, you might give this a try. It’s pretty inexpensive and easy! I started out with a piece of cabinet grade plywood.

I used my circular saw to cut it to the correct size.